Book a technician Samsung MultiXpress SL-K4300LX error codes Price a newer machine
Samsung MultiXpress SL-K4300LX error codes
Every service code group for the Samsung MultiXpress SL-K4250RX, SL-K4250LX, SL-K4300LX and SL-K4350LX, from the service manual, in plain words: what it means, and who clears it. Of the 37 groups below, 10 may clear with a restart, 20 you can clear yourself and 7 need a technician. Quote the full code when you book, and a technician arrives knowing what to bring.
The same codes sit with every other Samsung model in our Samsung error code guide.
These are the codes in the service manual for the MultiXpress K4 series that the Samsung error code guide does not already explain under another model.
K4 series: motors, fans and supplies
Codes from the error code section of the K4 series service manual.
| Code | What it means | Who clears it |
|---|---|---|
| A1-1111, A1-1113, A1-2111, A1-2113 | The registration and bypass (MP) motor (A1-111x) or the drum (OPC) motor (A1-211x) is not running, or is running while the machine reads it as stopped. Switch off and on; if it comes back, a technician is needed. | A restart may clear it |
| A1-5113, A1-5610 | A motor in the toner supply has a problem. Check the toner cartridge is seated properly, then switch off and on; if it comes back, a technician is needed. | A restart may clear it |
| A2-1510 to A2-2921 | A fan is not turning, or its signal is wrong. Check nothing is blocking the vents, then switch off and on; if it comes back, a technician replaces the fan. Codes in this group: A2-1510, A2-1511, A2-1521, A2-1523, A2-2611, A2-2613, A2-2810, A2-2811, A2-2821, A2-2823, A2-2910, A2-2911, A2-2920, A2-2921. | A technician |
| C1-1110, C1-111A | The toner cartridge is down to between 5 and 30 percent. Get a new one ready. | You can clear it |
| C1-1140, C1-1150, C1-1160, C1-1170 | The toner cartridge is at the end of its life. Replace it. | You can clear it |
| C1-1311, C1-1313, C1-1314 | Toner is not being supplied properly. Take the toner cartridge out, shake it gently side to side and refit it; if it comes back, a technician is needed. | A restart may clear it |
| C1-1411, C1-1512 | The toner cartridge is not fitted or its chip (CRUM) cannot be read (C1-1411), or it is not compatible with this machine (C1-1512). Fit or refit a cartridge made for this model. | You can clear it |
| C3-1110, C3-1130, C3-1140 | The imaging unit is nearly at the end of its life. Get a new one ready. | You can clear it |
| C3-1211, C3-1312 | The toner density sensor used for image stabilisation failed its calibration (C3-1211), or toner is not reaching the imaging unit properly (C3-1312). Switch off and on; if it comes back, a technician is needed. | A restart may clear it |
| C3-1411, C3-1414, C3-1512 | The imaging unit is not fitted or its chip cannot be read (C3-1411), its charger cannot be read (C3-1414), or it is not compatible (C3-1512). Fit or refit an imaging unit made for this model. | You can clear it |
| C3-1422 | The imaging unit needs cleaning. A technician cleans it. | A technician |
| C8-1130 | The developer unit has reached the end of its life. A technician replaces it. | A technician |
K4 series: paper, finisher and system
Paper and trays, the finisher, the document feeder, and the system codes.
| Code | What it means | Who clears it |
|---|---|---|
| H1-1312 to H1-1412 | Paper jam in tray 3 or tray 4: the pick up unit, the pick up rollers or the feed sensor. Open the tray and clear the paper. Codes in this group: H1-1312, H1-1313, H1-1314, H1-1315, H1-1412. | You can clear it |
| H1-1322, H1-1422, M1-3122, M1-3222 | A tray is pulled out, or its paper size sensor is not connected: tray 1 (M1-3122), tray 2 (M1-3222), tray 3 (H1-1322) or tray 4 (H1-1422). Push the tray in fully; if it stays, a technician checks the sensor. | You can clear it |
| H1-1351 to M1-5212 | A tray is below 10 percent of its paper, or its paper level sensor failed. Load paper; if it stays with the tray full, a technician checks the sensor. Codes in this group: H1-1351, H1-1352, H1-1354, H1-1451, H1-1452, H1-1454, M1-5111, M1-5113, M1-5120, M1-5211, M1-5212. | You can clear it |
| H1-5323, H1-5330 | The high capacity feeder's takeaway cover is open (H1-5323), or the machine cannot talk to the optional tray (H1-5330). Close the cover and check the tray is seated, then switch off and on; if it comes back, a technician is needed. | A restart may clear it |
| H2-6144, H2-6726, H2-6727 | The finisher is pulled out or not fitted properly (H2-6144), or its door is not closed (H2-6726, H2-6727). Push the finisher in and close its door. | You can clear it |
| H2-6211 to H2-6743 | A finisher part did not leave or reach its home position, or its motor did not run: the ejectors, the paper holding lever, the paper support, the transport motor, the paddle, the front or rear tamper, the stacker or the main tray. Clear any paper in the finisher and switch off and on; if it comes back, a technician is needed. Codes in this group: H2-6211, H2-6212, H2-6213, H2-6214, H2-6221, H2-6222, H2-6223, H2-6224, H2-6231, H2-6232, H2-6233, H2-6234, H2-6241, H2-6242, H2-6243, H2-6244, H2-6511, H2-6512, H2-6531, H2-6532, H2-6706, H2-6707, H2-6708, H2-6709, H2-6710, H2-6711, H2-6712, H2-6713, H2-6714, H2-6715, H2-6716, H2-6717, H2-6718, H2-6719, H2-6720, H2-6721, H2-6722, H2-6736, H2-6737, H2-6738, H2-6739, H2-6740, H2-6741, H2-6742, H2-6743. | A restart may clear it |
| H2-6311 to H2-6734 | The stapler or the hole punch did not leave or return to its home position, did not start up, or its motor did not run. Check for a jammed staple or punch waste, then switch off and on; if it comes back, a technician is needed. Codes in this group: H2-6311, H2-6321, H2-6322, H2-6323, H2-6324, H2-6331, H2-6332, H2-6333, H2-6334, H2-6411, H2-6421, H2-6422, H2-6423, H2-6424, H2-6551, H2-6552, H2-6728, H2-6729, H2-6730, H2-6731, H2-6734. | A restart may clear it |
| H2-6440, H2-6452 | The hole punch waste hopper is not fitted properly (H2-6440) or is full (H2-6452). Empty it and refit it. | You can clear it |
| H2-6700 to H2-6705 | Paper did not pass the finisher entrance. Open the finisher and clear the paper. Codes in this group: H2-6700, H2-6701, H2-6702, H2-6703, H2-6704, H2-6705. | You can clear it |
| H2-6723, H2-6724, H2-6725 | The set is too thick to staple (H2-6723), or the paper could not be moved to the stapling position (H2-6724, H2-6725). Staple fewer sheets and clear any paper in the finisher. | You can clear it |
| H2-6732, H2-6733, H2-6744, H2-6A63 | The staple cartridge needs refilling, or it is not fitted in the stapler. Refill or fit it. | You can clear it |
| H2-6735 | The finisher's top tray is full. Remove the printed paper. | You can clear it |
| H2-6A50 | The machine cannot talk to the finisher. Check it is docked and its cable is in, then switch off and on; if it comes back, a technician is needed. | A restart may clear it |
| M2-1121 to M3-1414 | Paper jam: in tray 1, tray 2 or the bypass tray, inside the machine at the feed or registration rollers, or around the fuser. Open the covers the panel shows and clear the paper. Codes in this group: M2-1121, M1-1213, M2-1131, M1-1613, M2-1124, M2-1125, M2-1134, M2-1135, M2-1211, M2-1213, M2-1214, M2-1331, M2-1333, M2-1334, M2-2111, M3-1413, M3-1414. | You can clear it |
| M1-4111, M1-4211 | Paper is not feeding from tray 1 (M1-4111) or tray 2 (M1-4211). Pull the tray out, check the paper and push it back in. | You can clear it |
| M3-2430 | The output tray or the inner tray is too full. Remove the printed paper. | You can clear it |
| S1-1113, S1-1114 | The main board's processor is overheating (S1-1113), or its fan is not working (S1-1114). A technician is needed. | A technician |
| S1-1313 | The saved date and time is not valid. Set the date and time on the panel. | You can clear it |
| S1-2111 to S2-2311 | A main board fault: memory not found at start up (S1-2111), the hard disk missing or failed (S1-2421, S1-2422), the MSOK chip not fitted properly or failed (S1-2510 to S1-2550), or the main board itself (S2-2311). A technician is needed. Codes in this group: S1-2111, S1-2421, S1-2422, S1-2510, S1-2520, S1-2550, S2-2311. | A technician |
| S1-4111, S1-4311, S1-5221, S4-3111 | A connection part failed: the main board cannot send data to the network (S1-4111), the USB chip (S1-4311), the wireless card is not found (S1-5221), or the fax card is not fitted properly (S4-3111). Switch off and on; if it comes back, a technician is needed. | A restart may clear it |
| S2-3321, S2-3421 | Toner supply is not enough (S2-3321): check the toner cartridge. S2-3421 means the machine is calibrating its toner density: wait for it to finish. | You can clear it |
| S3-3213 to U3-3122 | The document feeder (DSDF) is not connected or cannot talk to the scanner board, or its pick up module has a problem. Switch off and on; if it comes back, a technician is needed. Codes in this group: S3-3213, S3-3214, S3-3215, S3-3216, S3-3217, U3-3122. | A restart may clear it |
| U3-3311 to U3-4210 | Paper jam inside the document feeder or at its exit, or its cover is open (U3-4210). Open the feeder cover, clear the original and close the cover. Codes in this group: U3-3311, U3-3413, U3-3414, U3-3611, U3-3613, U3-3614, U3-4210. | You can clear it |
| U1-2141, U1-2142 | The fuser is too hot: its thermistor read above the maximum. Switch off and let it cool; if it comes back, a technician is needed. | A technician |
| U2-1111 to U2-6210 | The laser unit (LSU): its motor is not running properly (U2-1111 to U2-1114) or it is not fitted properly (U2-6210). A technician is needed. Codes in this group: U2-1111, U2-1112, U2-1113, U2-1114, U2-6210. | A technician |
Book a technician for the Samsung MultiXpress SL-K4300LX
Five quick details. We call you back within 1 business hour, Monday to Friday 8am to 5pm (Queensland time), to confirm the attendance charge and a time.
Rather talk now? Call 1300 922 260. Several machines, or an address to add? Use the full booking form.
Repair it, or replace it?
If the Samsung MultiXpress SL-K4300LX keeps showing the same codes, or a repair would cost more than the machine is worth, we can price a newer or refurbished one to buy outright, rent or lease, and look after it once it is in. Tell us what you need and we will come back with a price.
