Book a technician Sharp BP-30C25 error codes Price a newer machine
Sharp BP-30C25 error codes
Every service code group for the Sharp BP series (BP-30C25 and related models), from the service manual, in plain words: what it means, and who clears it. Of the 75 groups below, 7 may clear with a restart and 68 need a technician. Quote the full code when you book, and a technician arrives knowing what to bring.
The same codes sit with every other Sharp model in our Sharp error code guide.
First, the codes every Sharp model in this range shares.
H2 to H7: fusing
The fusing unit that melts the toner onto the page, its heater lamps and its thermistors.
| Code | What it means | Who clears it |
|---|---|---|
| H2-00, H2-01, H2-02 | A main or sub thermistor in the fusing unit reads open, so the machine cannot measure the fuser temperature. | A technician |
| H2-03, H2-05, H2-06 | A compensation or edge thermistor in the fusing unit reads open. | A technician |
| H3-00 | The fusing unit went over temperature at the upper main thermistor. Held until a technician cancels it. | A technician |
| H3-01, H3-02 | The fusing unit went over temperature at the lower main or upper sub thermistor. | A technician |
| H4-00 | The fusing unit did not reach its working temperature. Often the heater lamp, the thermostat, a thermistor or an interlock switch. | A technician |
| H4-01, H4-02 | The fusing unit ran too cold at the lower main or upper sub thermistor. | A technician |
| H4-30, H4-32 | A fusing thermistor reading does not match what the heater lamp should be doing, often because the lamp is not lighting. | A technician |
| H5-01 | Five jams in a row at the fusing exit, so the machine locks. Usually paper left inside, the exit sensor, or how the fusing unit is seated. | A technician |
| H7-10, H7-12 | The fusing unit could not recover its temperature after running cold. | A technician |
F2 and EE: toner, developer and process control
The toner cartridges, the developing units and the sensors that keep the image density right.
| Code | What it means | Who clears it |
|---|---|---|
| EE-EL | The automatic toner density setting failed with too much toner, usually after new developer. | A technician |
| EE-EU | The automatic toner density setting failed with too little toner. | A technician |
| EE-EC | The automatic toner density setting finished out of range. | A technician |
| F2-40, F2-41, F2-42, F2-43 | Toner density sensor fault in the black, cyan, magenta or yellow developing unit. | A technician |
| F2-64, F2-65, F2-66, F2-67 | Toner supply failed for one colour. The toner motor, the sensor, the cartridge or the toner pipe. | A technician |
| F2-70, F2-71, F2-72, F2-73 | The machine does not recognise the toner cartridge as the right one for it. | A technician |
| F2-74, F2-75, F2-76, F2-77 | The chip on a toner cartridge could not be read. | A technician |
C1 and C4: charging and transfer
The main chargers on the drums, and the high voltage that moves the image to the belt and then to the paper.
| Code | What it means | Who clears it |
|---|---|---|
| C1-10 | The main charger for black has an open or short circuit. The charger, its wiring or the developing unit. | A technician |
| C1-14 | The main charger for colour has an open or short circuit. | A technician |
| C1-15, C1-16, C1-40, C1-41 | Fault in the high voltage board or circuit that feeds the main chargers. | A technician |
| C4-00, C4-05 | PTC unit high voltage fault. The PTC unit is a replaceable part. | A technician |
| C4-20, C4-25 | Primary transfer high voltage fault, usually the primary transfer unit or its wiring. | A technician |
| C4-30, C4-31 | Secondary transfer high voltage open or shorted. | A technician |
E7 and L6: laser writing
The laser unit, which Sharp calls the LSU, that writes the image onto the drums.
| Code | What it means | Who clears it |
|---|---|---|
| L6-10 | The polygon motor in the laser unit has failed. | A technician |
| E7-20, E7-21, E7-22, E7-23 | The laser beam was not detected for black, cyan, magenta or yellow. | A technician |
| F2-49 | The laser unit temperature sensor is out of range or has failed. | A technician |
L4 and L8: motors, fans and power
The drive motors, cooling fans and mains power sensing.
| Code | What it means | Who clears it |
|---|---|---|
| L4-02 | The paper feed motor has failed. | A technician |
| L4-03 | The fusing motor has failed. | A technician |
| L4-06 | The transfer unit did not lift into or out of position. | A technician |
| L4-17, L4-18 | The drum motor for black or colour has locked. | A technician |
| L4-32, L4-35, L4-50, L4-51 | A cooling fan has stopped, on the power supply, the fusing unit or the process section. | A technician |
| L8-01, L8-02 | The mains power signal is missing or its frequency is out of range. The power unit or the supply. | A technician |
L1, L3, E6, E7 and U5: scanner and document feeder
The scanner, and the reversing or duplex single pass feeder on top.
| Code | What it means | Who clears it |
|---|---|---|
| L1-00, L3-00 | The scanner mirror unit did not move out or return. On a machine that has been moved, check the transport lock screw is out. | A technician |
| E7-10, E7-11, E7-14 | The scanner could not calibrate its black or white level, or its CCD board has a fault. | A technician |
| E6-10, E6-11, E6-14 | The same calibration fault in the part of the duplex feeder that reads the back of the page. | A technician |
| U5-00 | Communication lost with the document feeder. A restart may clear it. | A restart may clear it |
| U5-30, U5-31 | The document feeder tray did not lift or lower. | A technician |
F3 and U6: paper trays and feed options
The trays in the machine, the paper feed desk under it and the large capacity tray.
| Code | What it means | Who clears it |
|---|---|---|
| F3-12, F3-22 | Tray 1 or tray 2 did not lift. Check for a scrap of paper under the tray. Held until a technician cancels it. | A technician |
| U6-00, U6-20 | Communication lost with the paper feed desk or the large capacity tray. A restart may clear it. | A restart may clear it |
| U6-01, U6-02 | A tray in the paper feed desk did not lift. | A technician |
| U6-09, U6-23 | The large capacity tray did not lift or lower. | A technician |
F1: finishers
The inner finisher, the finishers and saddle stitch finisher, and the punch units.
| Code | What it means | Who clears it |
|---|---|---|
| F1-00 | Communication lost between the finisher and the machine. | A technician |
| F1-10 | The staple motor or the stapling operation has a fault. | A technician |
| F1-15 | The finisher exit tray lift motor has a fault. | A technician |
| F1-30, F1-32 | Communication lost between the finisher and its saddle unit or punch unit. | A technician |
| F1-37, F1-38 | Backup memory error on the finisher or punch board. A restart may clear it. | A restart may clear it |
E7: controller and storage
The main board, image memory, hard drive and SSD.
| Code | What it means | Who clears it |
|---|---|---|
| E7-03 | The hard drive has failed or is not connected properly. | A technician |
| E7-A7 | The mSATA SSD has failed or is not connected properly. | A technician |
| E7-90 | Communication lost between the main controller board and the engine board. | A technician |
| E7-01, E7-92, E7-93 | Image data could not be processed, often a memory or storage fault. | A technician |
| E7-C0, E7-C1 | Security board access or check error. Switching off and on may clear it. | A restart may clear it |
U1, U2, A0 and PC: memory, firmware and counters
The stored settings, counters, backup battery and firmware.
| Code | What it means | Who clears it |
|---|---|---|
| U1-01 | The backup battery on the main board is low and needs replacing. | A technician |
| U2-00, U2-11 | The settings memory, which holds the counters, could not be read or failed its check. | A technician |
| U2-30 | The manufacturing number stored on the main board and the engine board do not match, typically after a board replacement. | A technician |
| U2-40 | A storage area on the SSD has a file error. Switching off and on lets the machine restore it from the hard drive backup. | A restart may clear it |
| A0-01, A0-02 | The firmware on the engine or main board is damaged, often after a firmware update was interrupted. | A technician |
| A0-20, A0-21, A0-22 | The firmware and the stored data versions do not match. | A technician |
| PC | The machine is set to use a personal counter, and it cannot see one. | A technician |
Then the codes the Sharp BP series (BP-30C25 and related models) adds to those.
Sharp's BP series replaced the MX range. The BP-30C25 and its related BP models add these trouble codes to the lists above. They come from the service manual for the BP-30C25.
A0, E7 and F codes on the BP series: firmware, boards and image
Firmware, the main boards, the laser unit, sensors and toner.
| Code | What it means | Who clears it |
|---|---|---|
| A0-06, A0-17 to A0-19, A0-30 | Fax firmware, screen data, boot or machine setup error. Often after an interrupted update. Codes in this group: A0-17, A0-18, A0-19. | A technician |
| E7-04, E7-A8 | The storage chip or its controller failed its check. | A technician |
| E7-24 to E7-29, E7-99 | The laser driver for one colour, or its control chip or cable, has a fault. Codes in this group: E7-24, E7-25, E7-26, E7-27, E7-28, E7-29. | A technician |
| E7-49, E7-91, E7-94 | Watermark, received fax or image processing data is damaged. | A restart may clear it |
| E7-50, E7-55 | The engine board does not match its firmware or holds bad data. | A technician |
| E7-79, E7-80 | The network module or the scanner lost contact with the main board. | A restart may clear it |
| E7-C2, E7-C3 | The firmware is damaged. | A technician |
| F2-25 | The yellow discharge lamp has failed. | A technician |
| F2-39, F2-58 | A temperature or humidity sensor has failed. | A technician |
| F2-45, F2-78 | An image density sensor has failed. | A technician |
| F2-95 to F2-98 | A toner cartridge (black, cyan, magenta or yellow) did not eject properly. Codes in this group: F2-95, F2-96, F2-97, F2-98. | A technician |
| F6-98 | The fax board is for a different country than the machine. | A technician |
L, U and other codes on the BP series: drives, memory and options
Motors, saved data, the paper desk and the touch panel.
| Code | What it means | Who clears it |
|---|---|---|
| L4-01, L4-16 | The main motor or the fuser pressure release has failed. | A technician |
| U2-05, U2-14, U2-41, U2-42, U2-50, U2-70, U2-74, U2-80, U2-81, U2-90, U2-91 | Saved data is damaged: accounts, system settings, storage, adjustments, user login, OCR dictionary, recovery data or a board's memory chip. | A technician |
| U6-10, U6-50 to U6-55 | The paper desk jammed in its transport, does not suit the machine, lost contact or has the wrong firmware. Codes in this group: U6-50, U6-52, U6-55. | A technician |
| U7-51 | A coin or vending unit attached to the machine has a fault. | A technician |
| U9-01 | The touch panel has a fault. | A technician |
| UC-20 | An image chip error on the main board. | A technician |
Book a technician for the Sharp BP-30C25
Five quick details. We call you back within 1 business hour, Monday to Friday 8am to 5pm (Queensland time), to confirm the attendance charge and a time.
Rather talk now? Call 1300 922 260. Several machines, or an address to add? Use the full booking form.
Repair it, or replace it?
If the Sharp BP-30C25 keeps showing the same codes, or a repair would cost more than the machine is worth, we can price a newer or refurbished one to buy outright, rent or lease, and look after it once it is in. Tell us what you need and we will come back with a price.
